5Pcs DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
102
Direct purchase from the factory 
უსაფრთხო გადახდა
უფასო საჩუქარი
მიტანის პოლიტიკა
დაბრუნების პოლიტიკაუფასო საჩუქარი
მოგესალმებით Roymall-ში, თქვენს პრემიუმ საჩუქრების მაღაზიაში. ჩვენ ძალიან ვაფასებთ თქვენს მხარდაჭერას და მადლობის ნიშნად გთავაზობთ უფასო საჩუქარს ყოველ შეძენაზე. მზად ხართ გაეცნოთ ჩვენს კოლექციას? დაათვალიერეთ ჩვენი არჩევანი, განათავსეთ თქვენი შეკვეთა და დაელოდეთ თქვენს უფასო საჩუქარს თქვენი შეძენისთანავე.მიტანის პოლიტიკა
ჩვენ ვამუშავებთ შეკვეთებს 2 დღის განმავლობაში.სტანდარტული მიტანის დროა 5-7 სამუშაო დღე.მიტანის დრო შეიძლება განსხვავდებოდეს დანიშნულების მიხედვით.1. დაბრუნების პოლიტიკა
ჩვენ ვიღებთ მხოლოდ იმ ნივთების დაბრუნებას, რომლებიც შეძენილია roymall.com-დან. უფასო საჩუქრები არ შეიძლება დაბრუნდეს. ნივთი უნდა იყოს გამოუყენებელი და ორიგინალურ შეფუთვაში.ჩვენ ვამუშავებთ დაბრუნებას 3-5 სამუშაო დღეში მიღების შემდეგ.ინდივიდუალური ნივთები არ შეიძლება დაბრუნდეს.დაგვიკავშირდით: service@roymall.com ან Whatsapp: +86193598494712.ანაზღაურების პოლიტიკა
თქვენ მიიღებთ სრულ ანაზღაურებას ნივთის მიღებისა და შემოწმების შემდეგ. მიტანის ხარჯები არ არის დაბრუნებადი.დაგვიკავშირდით: service@roymall.com ან Whatsapp: +8619359849471
Specification:
n
n1.Input Voltage: DC10-14V
n2.Standby Current: <5MA
n3.RF Frequency: 433MHZ
n4.RF Working mode:Super heterodyne receiver
n5.Receiver Sensitivity: >90dBm
n6.Remote Control Distance: >100 meter(In open environment)
n7.Decoding Way: MCU Software decoding
n8.Can store the number of remote control:50
n9.Support remote control type: Fixed code, learning code
n10.Channel: 1CH
n11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
n12.Wiring Method:Fixed wiring terminal
n13.Working Voltage: DC12V
n14.Output Current: 10A
n15.Rated load:10A 250VAC / 10A 125VAC
n10A 30VDC / 10A 28VDC
n16.Output:Normally open,Common,Normally closed
n17.Dimension:3.5cm*3cm*1.6cm
n
nWorking/output way:
n
n1.Jog/Non-Latched: Press one button is Working /ON. Loosen your finger on the same button is Stop/OFF. One channel switch need one buttons remote control.
n2.Self -lock/Self-Latched: Press one button for one time is working/ON. Press the same button again is stop/OFF. One channel switch need one buttons remote control.
n3.Inter-lock /Latched: Press one button is working/ON, press another button is stop/OFF. One channel switch need 2 buttons remote control.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nDescription:
n
n1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
n2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
n3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nPackage included:
n
n5 x 12V 1CH 433MHz Wireless Relay Switch Receiver
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n1.Input Voltage: DC10-14V
n2.Standby Current: <5MA
n3.RF Frequency: 433MHZ
n4.RF Working mode:Super heterodyne receiver
n5.Receiver Sensitivity: >90dBm
n6.Remote Control Distance: >100 meter(In open environment)
n7.Decoding Way: MCU Software decoding
n8.Can store the number of remote control:50
n9.Support remote control type: Fixed code, learning code
n10.Channel: 1CH
n11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
n12.Wiring Method:Fixed wiring terminal
n13.Working Voltage: DC12V
n14.Output Current: 10A
n15.Rated load:10A 250VAC / 10A 125VAC
n10A 30VDC / 10A 28VDC
n16.Output:Normally open,Common,Normally closed
n17.Dimension:3.5cm*3cm*1.6cm
n
nWorking/output way:
n
n1.Jog/Non-Latched: Press one button is Working /ON. Loosen your finger on the same button is Stop/OFF. One channel switch need one buttons remote control.
n2.Self -lock/Self-Latched: Press one button for one time is working/ON. Press the same button again is stop/OFF. One channel switch need one buttons remote control.
n3.Inter-lock /Latched: Press one button is working/ON, press another button is stop/OFF. One channel switch need 2 buttons remote control.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nDescription:
n
n1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
n2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
n3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nPackage included:
n
n5 x 12V 1CH 433MHz Wireless Relay Switch Receiver
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
